Hoppe Replacement Gearboxes to Repair Your Existing HLS-9000 Manual Multipoint Door Lock – Repair Part
A Hoppe Replacement Gear Box makes is easy to repair your Hoppe Multi-point Door Lock. This works on all Hoppe HLS-9000 series. Manual Operation, Multipoint Lock Gear, 16mm & 20mm Faceplate. For the HLS-9000 Series (Handle Above Thumb Turn,) AVAILABLE IN 35MM, 45MM, 60MM and 70MM Backset, All with 25mm deadbolt throw. If you are not sure if this is the solution, Feel free to call us and discuss.
***Gearboxes below have the Mis-handling device wedge that are ON ALL CURRENT Hoppe Locks.***
Available Hoppe Manual Multipoint Lock Gearboxes
ALL CURRENT HOPPE LOCKS ARE EQUIPPED WITH A MIS-HANDLING DEVICE WEDGE
****HOPPE REPLACEMENT GEARBOXES WILL REPAIR ALL HLS-9000 MANUAL ACTIVATED MULTIPOINT LOCK SYSTEMS. WE TRY TO KEEP THESE IN STOCK AT ALL TIMES. THESE REPAIR PARTS SHIP OUT DAILY VIA USPS PRIORITY 2-3 DAY DELIVERY. ****
A Hoppe replacement gearbox lock case is the fastest way to repair your existing Hoppe multipoint door lock system. These gearboxes engage the panel edge locking points when lifting up on the lever handle. These gearboxes work on All Hoppe multipoint locks systems regardless if it is a Tongue, Roller Pin, Swing Hook, Round Bolt or 3 Point locks, with or without top and bottom shootbolts. This component drives the movement to the locking points, and corrects a drooping or sagging lever handle.
IWP-35-92-25
1 3/8″ Backset
IWP-45-92-25
1 3/4″ Backset
IWP-60-92-25
2 3/8″ Backset
IWP-70-92-25
2 3/4″ Backset
Hoppe Single Point Locks
Locks At Dead Bolt Only. NOT A MULTIPOINT LOCK REPAIR PART
Hoppe single point locks, only latch and lock at one point, and that is the dead bolt. Single point locks do not require lifting up on the lever handle in order to lock the door. Normal operation would be to close the door to latch shut, then to simply lock the dead bolt with the interior thumb turn or a key from the exterior.
1 3/8″ Backset
1/2″ Dead Bolt
1 3/8″ Backset
1″ Dead Bolt
1 3/4″ Backset
1/2″ Dead Bolt
1 3/4″ Backset
1″ Dead Bolt
2 3/8″ Backset
1″ Dead Bolt
2 3/4″ Backset
1″ Dead Bolt
Hoppe HLS-9000 Manual Multipoint Locks
Select Edge Lock Type (With Or Without Shoot Bolts)
All Locks Below are Based on 36″ Handle Height , EXCEPT FOR VARIABLE HANDLE HEIGHT UNITS LISTED BELOW
All Hoppe locks below have a set handle height of 36 Inches, with the exception of the variable 3 point and 2 point locks below. Some door manufacturers insisted on custom handle heights (OTHER THAN 36″), and Hoppe manufactured these per their requested specifications. If you cannot find the replacement lock that you need, Please contact us so our research team can find the lock you need or recommend an alternate solution to repair your door lock.
Tongue
Tongue
With Shoot Bolt
Roller Pin
Roller Pin
With Shoot Bolt
Round Bolt
Round Bolt
With Shoot Bolt
Swing Hook
Swing Hook
With Shoot Bolt
3 Point Lock
36″ Handle Height
2 Point In-Active Lock
36″ Handle Height
3 Point Lock
Variable Handle Height
2 Point In-Active Lock
Variable Handle Height
Hoppe Automatic Multipoint Locks
Automatically Engages Locking Points When Door Closes
36″ Handle Height, 42 1/4″ Roller Pin Release Trigger Measured Up From Bottom Of The Door.
All Hoppe AUTOMATIC locks below have a set handle height of 36 Inches, These locks work a little differently. Hoppe Automatic locks have a “trigger release roller pin” at 42 1/4″ from the bottom of the door panel, instead of a mis-handling device wedge between the striker latch and dead bolt. When closing the door, the trigger release strike a special mechanical keeper and fires the spring loaded lock to engage it’s edge locking points. Turn the thumb turn to lock the door. Lifting the lever handle is not necessary to engage locking points. Hoppe automatic locks are not offered with top and bottom shootbolts.
Automatic
Tongue
Automatic
Roller Pin